Key Features

• Function: power beyond sleeve ; isolates P from T in outlet section
• Valve family: AK 50 sectional control valves
• Porting: provides high pressure carry over to downstream valve
• Installation: fit in outlet body ; tank line must remain to T1.T2
• Use: extend circuits ; add additional valve stack safely

Key Features

• Sections: tandem two stage ; 14 cc front ; 14 cc rear
• Rotation: clockwise
• Ports: typical suction 3/4" BSP ; pressure 1/2" BSP per stage
• Shaft: 1.8 taper ; 4 bolt EU flange
• Working pressures: P1 up to 200 bar ; P2 up to 160 bar
• Speed: up to ~3500 rpm
• Use: dual circuit mobile hydraulics ; steering ; implements

Key Features

• Interface: banjo ring for 1/2" banjo bolt
• Tube end: 15 mm OD tube to suit 15L DIN 2353 compression fittings
• Overall length: 100 mm tube length
• Working pressure: up to 350 bar typical for steel banjo tubes
• Material: zinc plated steel body and tube
• Use: mount cylinders or valves where compact banjo connection is needed

Key Features

• Interface: 32 mm B shaft profile for MR motors
• Compatibility: MR series motor shaft conversion
• Keyway: parallel key drive (B type)
• Use: adapts motor to larger bore couplings and hubs
• Material: alloy steel; precision ground

Key Features

• Shaft type: Ø 32 mm parallel keyed output for MP ; MR motors
• Key standard: DIN 6885 ; ISO R773
• Key size: 10 x 8 mm typical for 30–38 mm shafts
• Compatibility: fits M+S MP ; MR families with CB shaft codes
• Use: service replacement shaft ; verify seal ; bearing diameters
• Applications: general LSHT drives; conveyors; augers

Key Features

• Valve family: OFC PRC 80 pressure relief cartridge ; M26x1.5
• Spring code: 30 set range 130–350 bar for PRC80
• Alt ranges: 10 5–50 bar ; 20 30–260 bar options
• Rated flow: 80 l.min cartridge capacity
• Max working pressure: 350 bar
• Adjustment styles: socket screw A ; handknob B ; tamperproof cap C
• Materials: zinc plated steel cartridge ; hardened internals

Key Features

• Ports: G 3/8 BSPP male x female
• Function: flow actuated hose burst safety valve
• Max flow: 45 l.min typical
• Max pressure: 350 bar
• Body: zinc plated steel ; compact inline
• Notes: install close to actuator port for best protection

Key Features

• Ports: G 3/8 BSPP
• Function: 90 deg elbow flow regulator with check valve
• Compensation: pressure compensated A->B ; free reverse via check
• Max flow A->B: 30 l.min typical at 3/8 size
• Max pressure: 250 bar
• Body: zinc plated steel ; alloy handknob
• Applications: speed control of cylinder or motor in one direction

Key Features

• Ports: G 3/8 BSPP female x female
• Function: flow operated hose burst safety shut off
• Max flow: 50 l.min typical
• Max pressure: 350 bar
• Body: zinc plated steel ; low leakage design
• Options: orifice in disc for emergency lowering on request
• Mounting: install at cylinder port ; use downstream flow regulator to control lowering

Key Features

• Shaft diameter: 25 mm
• Key standard: DIN 6885 parallel key
• Key size: 8 x 7 mm typical for 25 mm shaft
• Compatibility: M+S MP ; MR orbital motor shaft interface
• Material: steel ; ground finish on bearing ; seal lands
• Use: replacement straight keyed shaft ; service part

Key Features

• Shaft diameter: 1.000 in
• Key standard: ANSI B17.1 parallel key
• Key size: 1/4 in x 1/4 in typical for 1 in shaft
• Compatibility: M+S MP ; MR orbital motor shaft interface
• Use: replacement straight keyed shaft
• Notes: verify keyway and seal kit against motor series and code

Key Features

• Interface: 25 mm straight keyed shaft
• Compatibility: MR series hydraulic motors
• Keyway: parallel key for positive torque transfer
• Use: couples motor output to hubs; pulleys; couplings
• Material: alloy steel for durability

Key Features

• Spline profile: SAE 6B straight sided 1" 6-tooth per ANSI B92.1 class B
• Major diameter: 1.000 in nominal for SAE 6B
• Compatibility: M+S MP ; MR orbital motor shaft option
• Use: replacement output shaft for LSHT motors
• Material: steel ; typically hardened at spline flanks
• Mating hub: SAE 6B internal spline hub
• Typical applications: drives using 1 in 6B spline couplings ; gearboxes ; hubs

Key Features

• Compatibility: M+S MR series orbital motors series 3 ; series 4
• Shaft seal: 28.56 x 42 x 5.5 mm NBR typical
• Dust seal: 28.5 x 35 x 2 mm
• O rings: 48 x 2 mm ; 90 x 2 mm x3
• Purpose: restores sealing to reduce leakage and maintain pressure
• Use: service kit for MR motor overhaul ; maintenance
• Notes: check shaft code ZI ; different seals exist for ZH ; ZK variants

Key Features

• Interface: 1" straight keyed shaft
• Compatibility: MR series hydraulic motors (Zi)
• Keyway: parallel key for positive torque transfer
• Retention: snap ring/retainer provision (motor dependent)
• Material: alloy steel for wear resistance
• Use: adapts motor to couplings; hubs; pulleys

Key Features

• Type: OEM rotator seal kit
• Compatibility: model stated in title
• Contents: rod seals ; piston seals ; O rings ; wear rings
• Media: mineral hydraulic oil service
• Use: restore leak tightness and rotational performance

Key Features

• Type: complete double acting hydraulic cylinder assembly
• Compatibility: factory replacement for listed TG or GRX models
• Seals: high pressure rod and piston seals with wiper installed
• Ports: BSPP per OEM specification
• Testing: pressure tested for leakage and function
• Use: restores lifting and clamping performance

Key Features

• Function: normally closed proportional flow control
• Porting options: 2 way restrictive ; 3 way priority versions
• Pressure rating: 240 bar ; 260 bar ; 350 bar depending on model
• Nominal flow ranges: 40 l.min ; 57 l.min ; 65 l.min ; 114 l.min options
• Control: PWM current driven solenoid with dither for linearity
• Coil voltages: 12 vdc ; 24 vdc
• Connections: DIN 43650 ; Deutsch ; AMP coil connectors
• Mounting: screw in cartridge for common cavities 10W ; 12W ; 17A families
• Typical use: speed control of motors or actuators with pressure compensation

Key Features

• Input plug types: CEE 7/16 Europlug 2 pin ; CEE 7/7 Schuko E.F depending on model
• Output socket: BS 1363 Type G 3 pin
• Rating: 13 A 250 Vac
• Fuse: 13 A BS 1362
• Standard: BS 8546.2016+A1.2018 travel adaptor specification
• Safety features: shuttered outlets ; insulated construction
• Function: adapter only ; no voltage conversion
• Typical use: power EU equipment from UK mains 230 Vac

Key Features

• Thread size: G 3/8 BSPP
• Setting range: 10 to 180 bar adjustable
• Max flow: 35 l.min ; 45 l.min variants
• Max pressure: 350 bar
• Construction: zinc plated steel body ; hardened internal parts
• Seals: NBR Buna N standard
• Function: dual cross line relief with crossed tank
• Typical use: motor or cylinder shock protection with independent port settings

Key Features

• Body style: M18 threaded barrel flush mount
• Sensing range: 8 mm nominal
• Supply voltage: 10 to 30 vdc
• Output options: 2 wire dc ; PNP ; NPN ; NO ; NC variants
• Ingress protection: IP65 ; IP66 ; IP67 ; IP68 ; IP69K
• Switching frequency: 400 Hz typical
• Operating temperature: -40 to +85 degC
• Connection: M12 A coded connector ; 2 m PUR cable variants
• Standard: IEC 60947-5-2 inductive proximity

Key Features

• Series: FRD17 replacement element
• Diameter: 93 mm nominal element OD
• Filtration rating: 25 µm nominal media grade
• Intended use: particulate removal in hydraulic oil to protect components
• Applications: return ; suction or low pressure filter housings sized for FRD17 elements
• Service note: monitor differential pressure and change when indicator shows restriction

Key Features

• Thread: 3/8" BSPP ports
• Material: steel body for robustness
• Interface: accepts A2 size screw-in cartridge valve
• Use: manifold body for line-mounted control functions
• Service: suitable for industrial hydraulic circuits

Key Features

• Type: mechanical cable operation kit
• Length: 3.0 m
• Includes: lever ; cable ; mounting hardware
• Use: operate pto or valve from cab
• Application: hydraulic system component