Key Features

• Machine class: 1–3 t excavators
• Tilt angle: ±90 deg total 180 deg range depending on install
• Drive: rotary actuator power tilt
• Torque: ~900 N.m class
• Use: fine grading ; ditching ; battering in tight spaces

Key Features

• Gear ratio: 3 ; 1 step up
• Power rating: 10 kW maximum
• Input/output: 540 rpm PTO nominal to ~1620 rpm output
• Shafts: male 1 3/8 inch 6T PTO input
• Pump interface: Group 2 pump fitted ; suited to lower flow auxiliary circuits
• Housing: aluminium body ; compact size for light implements

Key Features

• Compatibility: Hydra Part sectional control valves nominal 50 L/min class ; one spool section
• Intended use: repack a single working section to cure external leaks and spool drag
• Typical kit contents: spool o rings ; end cap seals ; dust seals used on 50L sections
• Valve family: 3/8 inch port sectional valve spares range for 50 LPM systems
• Install tip: clean bore ; lightly lubricate seals ; verify spool end float after rebuild
• Result: restores smooth lever or solenoid actuation and reduces leakage to atmosphere

Key Features

• Compatibility: Hydra Part HP-20C Group 2 gear pumps including common 1.8 taper variants
• Intended use: replacement of front shaft seal and static seals during pump service
• Typical kit contents: shaft lip seal ; body o rings and gaskets as required for Group 2 pumps
• Reference performance: many Group 2 pumps in range rated up to 250 bar continuous service
• Application: agricultural PTO pumps ; mobile hydraulics ; general industrial systems
• Service note: inspect shaft journal and bushings ; replace if wear marks exceed spec

Key Features

• Compatibility: Baltrotors rotators GR30 ; GR30A ; GR30PF family
• Rotator type: Grapple rotator with eye upper connection and axle lower mount ; unlimited rotation
• Intended use: service kit for original seals used in GR30 series rotator heads
• Typical kit contents: rotary housing ; shaft and port sealing elements needed for leak repair
• Applications: forestry and small agricultural cranes using GR30 family rotators
• Fitment note: verify exact GR30 variant before installation to match geometry

Key Features

• Compatibility: Hydra Part cylinder series 203 ; 303 ; 403 ; 503
• Bore sizes: 30 ; 40 ; 50 ; 60/70 mm range options
• Intended use: complete reseal kit for the listed cylinder families
• Typical kit contents: seals for piston ; rod ; and wiper plus static rings as used in cylinder rebuild
• Applications: compact loaders ; attachments ; light industrial rams within these series
• Selection note: confirm series and bore from cylinder ID to match the correct kit option

Key Features

• Voltage: 12 vdc
• Power: 36 w
• Duty cycle: ed 100% ; continuous
• Application: coils for 45l ; 50l solenoid operated valves
• Connector: 4 pin style per data sheet
• Use: replacement coil only ; valve body not included

Key Features

• Compatibility: 45l monoblock valve series ; hydra part ; hydrocontrol m45 family
• Function: spring centered double acting spool positioner ; no detent
• Spool interface: 16 mm spool diameter per 45l valve spec
• System pressure (valve body ref): up to 315 bar
• Flow rating (valve body ref): nominal 45 l/min ; max 65 l/min
• Control options (valve family): manual lever ; cable ; pneumatic ; electro hydraulic
• Typical applications (valve family): wood splitters ; agricultural loaders ; small cranes

Key Features

• Applications: mobile hydraulics ; loaders ; cranes
• Compatibility: Hydra Part GS family ; alternative to Walvoil SD series in same size
• Fluid: mineral oil ; 15–75 cSt operating range
• Max pressure class: up to 315 bar per series

Key Features

• Series: 80L GS sectional control valve
• Applications: mobile hydraulics ; loaders ; cranes
• Compatibility: Hydra Part GS family ; alternative to Walvoil SD series in same size
• Fluid: mineral oil ; 15–75 cSt operating range
• Max pressure class: up to 315 bar per series

Key Features

• Lever thread: M10
• Overall length: 200 mm
• Knob diameter: 30 mm
• Compatibility: 45L ; 80L ; 90L ; 100L ; 120L ; 150L ; 240L valves
• Use: manual actuation of lever boxes

Key Features

• Kit: tie rods for 5 bank assembly . 4 rods per kit
• Thread: m10x1.5
• Rod length: 328 mm
• Compatibility: 100l gs sectional valves
• Function: clamps sections and endplates together

Key Features

• Part: tapered grub screw for carry over facility
• Thread: 3/8"
• Compatibility: 80l ; 100l ; 150l valve families
• Purpose: secures or blanks internal carry over drilling
• Use: fitted during conversion to power beyond or closed centre

Key Features

• Function: end cap for spool section ; closes body and retains hardware
• Compatibility: 90l ; 100l ; 120l ; 150l valve families
• Options: with stroke limiter ; without stroke limiter
• Maintenance: allows access to spring or detent kits
• Typical use: service replacement to restore manual lever feel

Key Features

• Function: power beyond ; feeds downstream valve
• Thread: 3/4" bsp
• Compatibility: 90l monoblock valves
• Use case: convert open center valve to series operation
• System rating: use with host valves up to 315 bar

Key Features

• Valve: 90L monoblock ; motor spool type 2
• Function: Spool for hydraulic motor circuits
• Use: Continuous motor drive with return to tank in neutral
• Additional info: See product data sheet for detailed measurements
• Neutral condition: Ports A ; B open in neutral for freewheeling motors

Key Features

• Function: Detent in A position ; positions 0 and B spring centered
• Kit code: 9B
• Compatibility: 80L ; 90L ; 100L ; 120L ; 150L control valves
• Use: Hold spool at full A
• Additional info: See product data sheet for detailed measurements

Key Features

• Function: Detent in B position ; positions 0 and A spring centered
• Kit code: 10B
• Compatibility: 80L ; 90L ; 100L ; 120L ; 150L control valves
• Use: Hold spool at full B
• Additional info: See product data sheet for detailed measurements

Key Features

• Function: 3 position detent ; holds spool in forward and reverse
• Compatibility: 90L ; 100L ; 120L ; 150L control valves
• Use: Motor circuits needing maintained actuation or float
• Install: Replaces end cap hardware on selected spool
• Additional info: See product data sheet for detailed measurements

Key Features

• Type: Rapidly biodegradable hydraulic fluid
• Viscosity options: ISO VG 32 ; ISO VG 46
• Base chemistry: Plant based or synthetic ester depending on grade
• Biodegradability: Typically > 90 percent per CEC L-33-T-82
• Use: For environmental applications where leaks must minimise impact
• Pack size: 205 Litre barrel

Key Features

• Pump group: Group 2 external gear pump
• Body: Aluminium body with cast iron end plates
• Shaft: 1/8 taper keyed
• Flange: 4 bolt European mount
• Ports: Inlet 1/2 inch BSPP ; outlet 3/8 inch BSPP typical
• Displacement range: ≈4 to 30 cc/rev options
• Continuous pressure: Up to ~250 bar depending on size

Key Features

• Compatibility: Hydra Part orbital motors ; ZHE model
• Motor series: MR ; MV
• Function: Service kit to renew shaft and housing seals ; restore leak tightness
• Intended fluid: Mineral hydraulic oils to ISO 11158 HM ; HLP
• Typical maintenance: Replace aged O-rings ; shaft seal when oil leakage or dust ingress occurs
• Applications: Orbital motors on mobile equipment ; agricultural implements ; conveyors

Key Features

• Type: female gear pump adaptor
• Orientation: 90°
• Port: per selection
• Mounting: 3 hole on 51 mm pcd
• Use: connect pump outlet to hose or fittings

Key Features

• Type: female gear pump adaptor
• Orientation: 90°
• Port: 1/2"
• Mounting: 4 hole on 40 mm pcd
• Use: connect pump outlet to hose or fittings