Key Features

• Gear ratio: 3 ; 1 speed increase
• Power rating: 20 kW
• Input coupling: female quick coupling PTO 1 3/8 inch 6 spline standard
• Pump interface: supplied with Group 3 gear pump for higher displacement
• Recommended limits: keep gearbox output below 3000 rpm per common PTO gearbox guidance
• Construction: aluminium gearbox for low mass on 3 point link implements

Key Features

• Compatibility: DAP8040 pattern cylinder used on CEL cylinder models only
• Bore x rod class: 80 x 40 mm nominal geometry per 8040 designation
• Intended use: complete reseal to address external leaks ; bypass and drift
• Typical kit contents: piston seal ; rod seal ; wiper ; and static seals commonly used
• Applications: general purpose rams on attachments and agricultural machinery
• Fitment note: verify CEL cylinder label before ordering to ensure correct kit series

Key Features

• Compatibility: Hydra Part MR high torque orbital motors ; Zi pattern
• Intended use: seal replacement for motor front end and housing to stop oil leakage
• Typical kit contents: shaft seal ; housing o rings ; drain and port seals typical for MR motors
• Applications: industrial and mobile hydraulic drives across compact machinery
• Service note: check case drain port condition ; replace washers if distorted
• Selection note: use motor nameplate to match the correct MR kit variant

Key Features

• Compatibility: Hydra Part MV high torque orbital motors ; Zi pattern
• Intended use: renew housing ; shaft and cover seals to prevent oil leakage and pressure loss
• Typical kit contents: shaft seal ; case drain and port seals ; body o rings used on MV motors
• Applications: drive motors on conveyors ; winches ; swing drives and attachments
• Service note: inspect shaft surface finish ; replace or sleeve if worn to protect new seal
• Fitment check: confirm MV motor code on nameplate to match kit version

Key Features

• Compatibility: Hydra Part HP-30C Group 3 aluminium gear pumps
• Intended use: service kit for shaft and static seals on Group 3 pump body
• Typical kit contents: front lip seal ; cover o rings and body seals for Group 3 construction
• Reference performance: Group 3 pumps in range typically used at higher flows and pressures
• Applications: PTO driven systems ; industrial power units requiring larger displacements
• Fitment check: confirm HP-30C family before ordering to ensure correct diameters

Key Features

• Compatibility: Hydra Part Group 2 tandem pumps using front code 067 ; rear code 066 interfaces
• Intended use: renew the sealing set when splitting tandem sections or replacing shaft seal
• Typical kit contents: shaft seal ; o rings ; interface seals used between tandem pump sections
• Notes on assembly: ensure rear shaft selection matches torque from front section during build
• Applications: tandem pumps on tippers ; loaders ; auxiliary hydraulic circuits
• Variant note: front 067 ; rear 066 code covers common Group 2 tandem configurations

Key Features

• Compatibility: Hydra Part HP-10C Group 1 gear pumps
• Intended use: renew shaft and static seals during Group 1 pump overhaul
• Typical kit contents: front shaft oil seal ; body o rings ; gasket elements for Group 1 casing
• Pump family: light duty aluminium gear pumps used widely on compact hydraulics
• Service note: check for shaft play ; replace bearings if excessive to protect new seal
• Applications: power packs ; small mobile circuits ; low to mid power implements

Key Features

• Compatibility: Hydra Part cylinder series 201 ; 301 ; 401 ; 501
• Bore sizes: 25 ; 30 ; 35 ; 40/50 mm options in one kit family
• Intended use: reseal of small bore cylinders within listed series to restore function
• Typical kit contents: piston ; rod ; wiper seals with static o rings used in cylinder rebuilds
• Applications: compact hydraulic rams on implements ; compact plant ; attachments
• Selection note: match cylinder series and bore at time of order to ensure fit

Key Features

• Compatibility: Hydra Part cylinder series 204 ; 304 ; 404 ; 504 ; 592
• Bore sizes: 40 ; 50 ; 63 ; 70/80 mm
• Intended use: reseal kit for mid size cylinders across the listed series
• Typical kit contents: piston ; rod ; wiper seals with associated o rings typical to service kits
• Applications: ag implements ; compact construction machines ; materials handling rams
• Fitment check: match series code on cylinder plate to ensure correct family selection

Key Features

• Compatibility: Hydra Part standard double acting cylinders ; bores 30 ; 40 ; 50 ; 60/70 ; 80 mm
• Intended use: routine reseal kit for compact and mid size standard cylinders
• Typical kit contents: dynamic piston and rod seals ; wiper and static sealing elements typical for rebuild
• Applications: compact machinery ; auxiliary rams ; attachments
• Fitment check: verify bore and rod combo to select the correct sub option within the range
• Service note: install with clean fluid and avoid sharp edges to protect sealing lips

Key Features

• Compatibility: Hydra Part cylinder series 205 ; 305 ; 405 ; 505 ; 593 ; 612 ; 632 ; 642 ; 651
• Bore sizes: 40 ; 50 ; 63 ; 70 ; 80/90 mm
• Intended use: service kit for resealing listed series cylinders to prevent leakage and drift
• Typical kit contents: rod seal ; piston seal ; wiper ; backup rings and o rings as required
• Applications: mobile hydraulic cylinders across ag ; municipal and light construction machinery
• Selection note: match series and bore markings to ensure compatibility across the variant list

Key Features

• Compatibility: Hydra Part cylinder series 206 ; 306 ; 406 ; 506
• Bore sizes: 50 ; 63 ; 70 ; 80/90 ; 100 mm range
• Intended use: resealing of medium bore cylinders in the specified series to recover performance
• Typical kit contents: piston ; rod ; wiper and related static seals typical to cylinder service kits
• Applications: suitable for rams on trailers ; loaders ; compact equipment within these series
• Fitment check: use the series code stamped on the cylinder to select the correct kit

Key Features

• Compatibility: Hydra Part standard double acting cylinders ; larger bores 70 ; 80 ; 90 ; 100 ; 110 ; 125 ; 130/150 mm
• Intended use: service kit for major reseal of large bore standard cylinders
• Typical kit contents: dynamic seals for piston and rod ; wiper ; and static seals typical for rebuild
• Application range: heavy mobile plant ; materials handling ; forestry and similar equipment
• Sizing note: check both bore and rod dimensions to match the correct sub option within the range
• Service guidance: clean grooves and lightly lubricate seals during assembly to avoid damage

Key Features

• Compatibility: Hydra Part cylinder series 207 ; 307 ; 407 ; 507
• Bore sizes: 50 ; 63 ; 70 ; 80 ; 90 ; 100/115 mm options combined in range
• Intended use: complete reseal of specified series cylinders during overhaul or preventive maintenance
• Typical kit contents: piston seal ; rod seal ; wiper ; static o rings as used in cylinder rebuilds
• Use case: suited to construction ; agricultural and industrial rams within the listed series
• Fitment check: confirm cylinder plate or purchase record for exact series before fitment

Key Features

• Compatibility: Hydra Part standard double acting cylinders ; bores 45 ; 80/90 mm
• Intended use: rebuild and reseal standard cylinders to restore pressure integrity and stop external leakage
• Typical kit contents: piston ; rod ; buffer and wiper seals plus associated o rings for cylinder service
• Applications: general mobile hydraulics ; loaders ; attachments ; ag and industrial equipment
• Maintenance note: verify bore ; rod ; and series before ordering to match correct seal sizes
• Fluid compatibility: formulated for use with mineral hydraulic oils common to mobile machinery

Key Features

• Section type: mid inlet (e12) with pressure relief
• Compatibility: 50l gs sectional valve
• Function: adds pump inlet mid stack and adjustable relief
• Typical flow class: 50 l/min nominal
• Relief range (typical): 0 ; 315 bar adjustable

Key Features

• Type: fixed port relief ; anti cavitation (rpht)
• Setting: 220 bar
• Compatibility: 80l ; 100l ; 150l ; 240l working port cavities
• Purpose: limits port pressure spikes and prevents cavitation
• Other settings: 100 ; 120 ; 140 ; 160 ; 180 ; 200 ; 240 ; 260 bar options

Key Features

• Kit: 8ep4 on/off electro pneumatic kit with manifold
• Voltage: 24 vdc
• Compatibility: 45l ; 50l valve families
• Purpose: remote electrical actuation via air cylinder on spool
• Controls: works with radio remote or switch outputs

Key Features

• Kit: 8ep4 on/off electro pneumatic kit with manifold
• Voltage: 12 vdc
• Compatibility: 45l ; 50l valve families
• Purpose: remote electrical actuation via air cylinder on spool
• Controls: works with radio remote or switch outputs

Key Features

• Spool type: motor spool (type 2)
• Compatibility: 100l gs sectional working section
• Spool diameter (family): 20 mm interchangeable spools
• Intended use: bidirectional hydraulic motor control
• Options: kits for detent ; stroke limiters ; auxiliary valves

Key Features

• Section type: left inlet (ac) with pressure relief
• Port size: 3/4" bsp
• Compatibility: 100l gs sectional control valve
• Function: pump inlet and adjustable system relief
• Relief range (typical): 60 ; 315 bar adjustable

Key Features

• Voltage: 24 vdc
• Power: 37 w
• Duty cycle: ed 100% ; continuous
• Application: coils for 45l ; 50l solenoid operated valves
• Connector: 4 pin style per data sheet
• Use: replacement coil only ; valve body not included

Key Features

• Section type: left inlet (ac)
• Compatibility: 80l gs sectional control valve
• Old reference: 30085749
• Includes: direct acting pressure relief valve
• Relief range (typical): 25 ; 315 bar adjustable
• Function: main pump inlet ; overpressure protection

Key Features

• Section type: tank/outlet section (tc)
• Compatibility: 80l gs sectional control valve
• Function: provides main return to tank port for the valve stack
• Old reference: 30085660
• Typical circuits: open centre with optional carry over porting