Key Features

• Mounting interfaces: PTO EN.ISO 4 bolt to UNI 3 bolt
• Integrated bearing: one ball bearing
• Max torque: 315 N.m
• Max power at 1000 rpm: 33 kW
• Use case: fit UNI 3 bolt pumps to ISO 4 bolt PTO housings
• Construction: steel adaptor with precision machining
• Accessories: studs ; gaskets available in kits

Key Features

• Interface: cetop 5 ; ng10 valve
• Function: manual override cap for solenoid operator
• Install: screws on actuator end
• Use: manual actuation during service or power loss
• Application: hydraulic system component

Key Features

• Motor series: Group 2 gear motor
• Displacement: 14 cc.rev
• Mount: European 4 bolt flange ; 1.8 taper shaft
• Ports: BSP
• Drain: external case drain recommended for reversible use

Key Features

• Machine class: 1–3 t excavators
• Tilt angle: ±90 deg total 180 deg range depending on install
• Drive: rotary actuator power tilt
• Torque: ~900 N.m class
• Use: fine grading ; ditching ; battering in tight spaces

Key Features

• Gear ratio: 3 ; 1 step up
• Power rating: 10 kW maximum
• Input/output: 540 rpm PTO nominal to ~1620 rpm output
• Shafts: male 1 3/8 inch 6T PTO input
• Pump interface: Group 2 pump fitted ; suited to lower flow auxiliary circuits
• Housing: aluminium body ; compact size for light implements

Key Features

• Gear ratio: 3 ; 1 step up for pump speed
• Power rating: 20 kW maximum
• Input/output: 540 rpm PTO nominal to ~1620 rpm output ; observe 3000 rpm max output guidance
• Shafts: male PTO 1 3/8 inch 6 spline interface
• Pump interface: supplied with Group 3 gear pump for higher flow demand
• Construction: lightweight aluminium gearbox for agricultural PTO duty

Key Features

• Compatibility: Hydra Part MSY series disc valve orbital motors ; Zi pattern
• Motor notes: MSY motors use disc valve distribution offering higher torque capability in family
• Intended use: seal replacement for output shaft ; cover and porting to resolve leaks
• Typical kit contents: shaft seal ; housing o rings ; drain port seals commonly replaced on service
• Applications: industrial and mobile drives requiring rugged low speed high torque performance
• Selection note: check MSY displacement code and mounting to select correct kit

Key Features

• Compatibility: Hydra Part sectional control valves nominal 50 L/min class ; one spool section
• Intended use: repack a single working section to cure external leaks and spool drag
• Typical kit contents: spool o rings ; end cap seals ; dust seals used on 50L sections
• Valve family: 3/8 inch port sectional valve spares range for 50 LPM systems
• Install tip: clean bore ; lightly lubricate seals ; verify spool end float after rebuild
• Result: restores smooth lever or solenoid actuation and reduces leakage to atmosphere

Key Features

• Compatibility: Hydra Part HP-20C Group 2 gear pumps including common 1.8 taper variants
• Intended use: replacement of front shaft seal and static seals during pump service
• Typical kit contents: shaft lip seal ; body o rings and gaskets as required for Group 2 pumps
• Reference performance: many Group 2 pumps in range rated up to 250 bar continuous service
• Application: agricultural PTO pumps ; mobile hydraulics ; general industrial systems
• Service note: inspect shaft journal and bushings ; replace if wear marks exceed spec

Key Features

• Compatibility: Baltrotors rotators GR30 ; GR30A ; GR30PF family
• Rotator type: Grapple rotator with eye upper connection and axle lower mount ; unlimited rotation
• Intended use: service kit for original seals used in GR30 series rotator heads
• Typical kit contents: rotary housing ; shaft and port sealing elements needed for leak repair
• Applications: forestry and small agricultural cranes using GR30 family rotators
• Fitment note: verify exact GR30 variant before installation to match geometry

Key Features

• Compatibility: Hydra Part cylinder series 203 ; 303 ; 403 ; 503
• Bore sizes: 30 ; 40 ; 50 ; 60/70 mm range options
• Intended use: complete reseal kit for the listed cylinder families
• Typical kit contents: seals for piston ; rod ; and wiper plus static rings as used in cylinder rebuild
• Applications: compact loaders ; attachments ; light industrial rams within these series
• Selection note: confirm series and bore from cylinder ID to match the correct kit option

Key Features

• Compatibility: Hydra Part standard cylinders ; bores 35 ; 40 ; 50 ; 60/70 mm
• Intended use: reseal kit to address external leaks ; internal bypass and poor cylinder holding
• Typical kit contents: piston seal ; rod seal ; wiper ; static seals as typically included in kits
• Applications: light plant ; agricultural implements ; compact handling equipment
• Sizing note: measure bore and rod to ensure correct option under the 35 ; 60/70 set
• Install tip: use appropriate assembly sleeves to avoid cutting PTFE or elastomer lips

Key Features

• Voltage: 12 vdc
• Power: 36 w
• Duty cycle: ed 100% ; continuous
• Application: coils for 45l ; 50l solenoid operated valves
• Connector: 4 pin style per data sheet
• Use: replacement coil only ; valve body not included

Key Features

• Compatibility: 45l monoblock valve spool set (1 x spool)
• Purpose: replace worn spool seals to reduce internal leakage and restore performance
• Kit coverage: seals for one spool only
• Cleanliness target (valve family): iso 4406 class 19/16
• Typical medium: mineral hydraulic oil iso vg 32 ; 46
• Installation note: lubricate seals and avoid damage during spool insertion

Key Features

• Compatibility: 45l monoblock valve series ; hydra part ; hydrocontrol m45 family
• Function: spring centered double acting spool positioner ; no detent
• Spool interface: 16 mm spool diameter per 45l valve spec
• System pressure (valve body ref): up to 315 bar
• Flow rating (valve body ref): nominal 45 l/min ; max 65 l/min
• Control options (valve family): manual lever ; cable ; pneumatic ; electro hydraulic
• Typical applications (valve family): wood splitters ; agricultural loaders ; small cranes

Key Features

• Applications: mobile hydraulics ; loaders ; cranes
• Compatibility: Hydra Part GS family ; alternative to Walvoil SD series in same size
• Fluid: mineral oil ; 15–75 cSt operating range
• Max pressure class: up to 315 bar per series

Key Features

• Series: 80L GS sectional control valve
• Applications: mobile hydraulics ; loaders ; cranes
• Compatibility: Hydra Part GS family ; alternative to Walvoil SD series in same size
• Fluid: mineral oil ; 15–75 cSt operating range
• Max pressure class: up to 315 bar per series

Key Features

• Series: 150L GS sectional control valve
• Bank size: 5 bank
• Length: 366 mm
• Thread: M10x1.5
• Applications: mobile hydraulics ; loaders ; cranes

Key Features

• Type: 2 axis mechanical joystick . lcb layout
• Compatibility: Hydra Part 45L monobloc valve series
• Function: controls two spools with cross pattern motion
• Use: loaders ; cranes ; attachments
• Integration: mechanical linkages and brackets included

Key Features

• Function: single microswitch kit for spool position sensing
• Compatibility: 45l ; 50l control valves
• Switch types: normally open ; normally closed options
• Use: auxiliary electrical signal for interlocks or lights
• Mounting: fits spring cap positioner hardware

Key Features

• Function: high pressure carry over ; power beyond
• Thread: 3/8" bsp
• Compatibility: 80l ; 100l ; 150l valve families
• Use case: connect upstream valve to downstream control valve
• System rating: for host valves operating to 315 bar

Key Features

• Spool type: motor spool type 2
• Application: bi directional hydraulic motors
• Behavior: neutral geometry reduces load shock and cavitation
• Compatibility: 45l monobloc valve series
• Positions: 3 position ; spring return to neutral

Key Features

• Actuation: pneumatic cylinder kit for remote spool operation
• Compatibility: 45l ; 50l control valves
• Use case: enables air control from cab or panel
• Integration: works with 3/2 electro pneumatic valves in 8ep3 ; 8ep4 systems
• Benefit: isolates operator from hydraulic leaks ; improves ergonomics

Key Features

• Function: end cap for spool section ; closes body and retains hardware
• Compatibility: 90l ; 100l ; 120l ; 150l valve families
• Options: with stroke limiter ; without stroke limiter
• Maintenance: allows access to spring or detent kits
• Typical use: service replacement to restore manual lever feel