Key Features

• Compatibility: HP50 monoblock control valve sections
• Assembly: complete wet spool lever cap with lever hardware
• Rated flow of valve: 50 l.min HP50 valve family
• Seal type: wet armature design with O ring sealing
• Use: service kit to replace damaged cap ; restores manual actuation

Key Features

• Interface: banjo ring for 1/2" banjo bolt
• Tube end: 15 mm OD tube to suit 15L DIN 2353 compression fittings
• Overall length: 100 mm tube length
• Working pressure: up to 350 bar typical for steel banjo tubes
• Material: zinc plated steel body and tube
• Use: mount cylinders or valves where compact banjo connection is needed

Key Features

• Ports: G 3/8 BSPP
• Function: 3 way pressure compensated priority flow control
• Max inlet flow: 60 l.min
• Max outlet C flow: 35 l.min
• Max pressure: 270 bar
• Body: aluminium body ; hardened steel internals
• Use: set constant actuator flow with excess to tank or secondary circuit

Key Features

• Ports: G 3/8 BSPP female x female
• Function: flow operated hose burst safety shut off
• Max flow: 50 l.min typical
• Max pressure: 350 bar
• Body: zinc plated steel ; low leakage design
• Options: orifice in disc for emergency lowering on request
• Mounting: install at cylinder port ; use downstream flow regulator to control lowering

Key Features

• Ports: G 3/4 BSPP
• Function: 3 way priority flow control ; excess to S line
• Max inlet flow: 150 l.min
• Max regulated flow: up to 90 l.min adjustment range
• Max pressure: 260 bar
• Body: aluminium body ; hardened internal parts
• Adjustment: twin handknob ; lockable
• Typical use: steering priority ; auxiliary circuits from single pump

Key Features

• Compatibility: M+S MR series orbital motors series 3 ; series 4
• Shaft seal: 28.56 x 42 x 5.5 mm NBR typical
• Dust seal: 28.5 x 35 x 2 mm
• O rings: 48 x 2 mm ; 90 x 2 mm x3
• Purpose: restores sealing to reduce leakage and maintain pressure
• Use: service kit for MR motor overhaul ; maintenance
• Notes: check shaft code ZI ; different seals exist for ZH ; ZK variants

Key Features

• Thread: metric M5
• Length: 110 mm
• Head: socket cap
• Material: high tensile steel (typical)
• Use: hydraulic assemblies; brackets; adapters
• Drive: internal hex for controlled tightening

Key Features

• Mounting interfaces: PTO EN.ISO 4 bolt to UNI 3 bolt
• Integrated bearing: one ball bearing
• Max torque: 315 N.m
• Max power at 1000 rpm: 33 kW
• Use case: fit UNI 3 bolt pumps to ISO 4 bolt PTO housings
• Construction: steel adaptor with precision machining
• Accessories: studs ; gaskets available in kits

Key Features

• Type: mechanical cable operation kit
• Length: 3.0 m
• Includes: lever ; cable ; mounting hardware
• Use: operate pto or valve from cab
• Application: hydraulic system component

Key Features

• Type: bonded seal ; dowty washer
• Size: 1/2"
• Elastomer: nitrile nbr
• Use: seals bspp bolt faces ; banjo fittings
• Application: hydraulic system component

Key Features

• Motor series: Group 2 gear motor
• Displacement: 14 cc.rev
• Mount: European 4 bolt flange ; 1.8 taper shaft
• Ports: BSP
• Drain: external case drain recommended for reversible use

Key Features

• Machine class: 1–3 t excavators
• Tilt angle: ±90 deg total 180 deg range depending on install
• Drive: rotary actuator power tilt
• Torque: ~900 N.m class
• Use: fine grading ; ditching ; battering in tight spaces

Key Features

• Gear ratio: 3 ; 1 step up
• Power rating: 10 kW maximum
• Input/output: 540 rpm PTO nominal to ~1620 rpm output
• Shafts: male 1 3/8 inch 6T PTO input
• Pump interface: Group 2 pump fitted ; suited to lower flow auxiliary circuits
• Housing: aluminium body ; compact size for light implements

Key Features

• Gear ratio: 3 ; 1 step up for pump speed
• Power rating: 20 kW maximum
• Input/output: 540 rpm PTO nominal to ~1620 rpm output ; observe 3000 rpm max output guidance
• Shafts: male PTO 1 3/8 inch 6 spline interface
• Pump interface: supplied with Group 3 gear pump for higher flow demand
• Construction: lightweight aluminium gearbox for agricultural PTO duty

Key Features

• Compatibility: Hydra Part MT orbital motors ; Zi pattern
• Intended use: renew shaft ; cover and case seals to correct oil leaks and pressure loss
• Typical kit contents: output shaft seal ; body o rings ; port and drain seals used on MT motors
• Applications: low speed high torque drives on conveyors ; wheel motors ; winches
• Service note: inspect shaft for wear ; replace if grooved to protect new seal
• Fitment check: confirm MT model code and mounting to select correct kit

Key Features

• Compatibility: Hydra Part MSY series disc valve orbital motors ; Zi pattern
• Motor notes: MSY motors use disc valve distribution offering higher torque capability in family
• Intended use: seal replacement for output shaft ; cover and porting to resolve leaks
• Typical kit contents: shaft seal ; housing o rings ; drain port seals commonly replaced on service
• Applications: industrial and mobile drives requiring rugged low speed high torque performance
• Selection note: check MSY displacement code and mounting to select correct kit

Key Features

• Compatibility: Hydra Part sectional control valves nominal 50 L/min class ; one spool section
• Intended use: repack a single working section to cure external leaks and spool drag
• Typical kit contents: spool o rings ; end cap seals ; dust seals used on 50L sections
• Valve family: 3/8 inch port sectional valve spares range for 50 LPM systems
• Install tip: clean bore ; lightly lubricate seals ; verify spool end float after rebuild
• Result: restores smooth lever or solenoid actuation and reduces leakage to atmosphere

Key Features

• Compatibility: Hydra Part HP-20C Group 2 gear pumps including common 1.8 taper variants
• Intended use: replacement of front shaft seal and static seals during pump service
• Typical kit contents: shaft lip seal ; body o rings and gaskets as required for Group 2 pumps
• Reference performance: many Group 2 pumps in range rated up to 250 bar continuous service
• Application: agricultural PTO pumps ; mobile hydraulics ; general industrial systems
• Service note: inspect shaft journal and bushings ; replace if wear marks exceed spec

Key Features

• Compatibility: Baltrotors rotators GR30 ; GR30A ; GR30PF family
• Rotator type: Grapple rotator with eye upper connection and axle lower mount ; unlimited rotation
• Intended use: service kit for original seals used in GR30 series rotator heads
• Typical kit contents: rotary housing ; shaft and port sealing elements needed for leak repair
• Applications: forestry and small agricultural cranes using GR30 family rotators
• Fitment note: verify exact GR30 variant before installation to match geometry

Key Features

• Compatibility: Hydra Part cylinder series 200 ; 300 ; 400 ; 500
• Bore sizes: 20 ; 25 ; 30/32 ; 40 mm
• Intended use: reseal kit for small bore standard cylinders used on compact equipment
• Typical kit contents: piston ; rod ; wiper seals and static rings typically supplied for rebuild
• Applications: small actuators on trailers ; clamps ; light duty machinery
• Selection note: use bore size and series number to choose correct kit option

Key Features

• Compatibility: Hydra Part cylinder series 203 ; 303 ; 403 ; 503
• Bore sizes: 30 ; 40 ; 50 ; 60/70 mm range options
• Intended use: complete reseal kit for the listed cylinder families
• Typical kit contents: seals for piston ; rod ; and wiper plus static rings as used in cylinder rebuild
• Applications: compact loaders ; attachments ; light industrial rams within these series
• Selection note: confirm series and bore from cylinder ID to match the correct kit option

Key Features

• Compatibility: Hydra Part standard cylinders ; bores 35 ; 40 ; 50 ; 60/70 mm
• Intended use: reseal kit to address external leaks ; internal bypass and poor cylinder holding
• Typical kit contents: piston seal ; rod seal ; wiper ; static seals as typically included in kits
• Applications: light plant ; agricultural implements ; compact handling equipment
• Sizing note: measure bore and rod to ensure correct option under the 35 ; 60/70 set
• Install tip: use appropriate assembly sleeves to avoid cutting PTFE or elastomer lips

Key Features

• Type: microswitch ; normally open
• Thread: m14 x 1.5
• Use: lever position sensing ; electrical signalling on control valves
• Mounting: screws into dedicated boss on lever box/actuator kit
• Contact rating: suits low current control circuits ; use relay for higher loads

Key Features

• Series: 80L GS sectional control valve
• Applications: mobile hydraulics ; loaders ; cranes
• Compatibility: Hydra Part GS family ; alternative to Walvoil SD series in same size
• Fluid: mineral oil ; 15–75 cSt operating range
• Max pressure class: up to 315 bar per series